On 13 November 2026 a 19-patch series titled “riscv: add initial support
for the Allwinner V861 and Avaota F2” reached the RISC-V and devicetree lists, posted through the B4
relay by Han Gao (gaohan@iscas.ac.cn) of the Institute of Software, Chinese
Academy of Sciences (ISCAS). The cover letter is one sentence long: the Allwinner V861 is a camera SoC with
two XuanTie C907 harts; the series adds the clock controllers, the pin controllers, the RTC clocks
and the device trees needed to boot the YuzukiHD Avaota F2 board to a serial console — and it
was tested on the Avaota F2 itself. Twenty-six files, +2,080/−9 lines, base commit
6628e7d4c6b2, status: new, under review. With it, the V861 becomes the
second Allwinner RISC-V SoC to enter the mainline kernel after the D1 — and the first one
whose vendor software reality is an OpenWrt fork rather than a buildroot-style distro.
Allwinner has not published an English datasheet, so the product picture below comes from vendor materials as
compiled by CNX Software (2 October 2026) and from the Avaota F2 documentation ecosystem —
treat it as the vendor’s account, not a measured one. The V861M2-XXX pairs two XuanTie
C907 cores (RV64GCBV) up to 1.4 GHz with one XuanTie E907 (RV32IMAFC) up to 800 MHz
that runs an RTOS, an H.264/H.265 encoder rated to 4K@25fps, (M)JPEG handling up to
8192×8192, a decoder rated to 1080p60, and a 1 TOPS (INT8) NPU that
Allwinner markets under the name “AI-ISP 2.0”. Memory is 128 MB of DDR3
in-package plus 16 MB of NOR flash and a microSD slot. The target product is a pan-tilt AI camera:
4-lane and 2-lane MIPI CSI, GC2083 (1080p30) or GC8613 (4K@15) sensors, a speaker and two microphone inputs, and an
AXP333 power-management IC that also drives the pan-tilt motors. The vendor SDK’s profile list — ipc,
aov (always-on video), aiglass, perf — tells you exactly which products this family is for.
| Item | Published value | Source & status |
|---|---|---|
| CPU | 2× XuanTie C907, RV64GCBV, up to 1.4 GHz | Vendor materials via CNX Software; core identity confirmed by mainline DT (csky,c907) |
| Companion core | 1× XuanTie E907, RV32IMAFC, up to 800 MHz (RTOS) | Vendor materials; absent from the mainline device tree |
| Video | H.264/H.265 encode to 4K@25fps; (M)JPEG to 8192×8192; decode to 1080p60 | Vendor materials; no mainline driver in this series |
| AI | 1 TOPS INT8 NPU, branded “AI-ISP 2.0” | Vendor materials; no mainline driver |
| Memory | 128 MB DDR3 in-package; 16 MB NOR (PY25Q128); microSD | Vendor materials; capacity fixed by packaging |
| Camera input | 4-lane + 2-lane MIPI CSI; GC2083 1080p30, GC8613 4K@15 | Vendor materials + board docs |
| Board | Avaota F2, ~40×22 mm, 6 layers, AXP333 PMU + motor pads | Open hardware, CC0 (schematic, EasyEDA PCB, Gerber, STEP, BOM, pick-and-place) |
The 19 patches are deliberately narrow: make a C907 hart with a UART reach userspace from a mainline build. The
bulk of the work is the clock tree — ccu-sun252i-v861.c alone is 1,117 lines —
plus the always-on domain and the RTC, whose driver needed two small generalizations (a variant without a 32k fanout
mux, another 24 MHz-to-32k divider ratio) before the V861’s RTC block could reuse the venerable
sun6i-rtc code. Pinctrl comes as PIO and R-PIO controllers, one of which required a shared-infrastructure
change: a per-controller IRQ register base. Platform naming follows the Allwinner convention: where the D1 lived on
sun20i, the V861 lives on sun252i.
| Patches | Content | Size |
|---|---|---|
| 1–2 | ARCH_SUNXI Kconfig broadened from “Allwinner sun20i SoCs” to “Allwinner SoCs” (D1, D1s and now V861); XuanTie C907 added to the RISC-V CPU bindings | +3/−3 |
| 3–5 | Bindings: V861 PLIC (150 sources), V861 CLINT, V861 CCUs | ~110 lines |
| 6–7 | ccu-sun252i-v861.c main CCU + PRCM CCU (ccu-sun252i-v861-r.c) | 1,117 + 110 lines |
| 8–11 | RTC bindings + three sun6i-rtc clock-driver generalizations for the V861 RTC | +31 net |
| 12–15 | Pin controller bindings + per-controller IRQ register base in the sunxi pinctrl core + PIO + R-PIO | ~120 lines |
| 16–18 | SoC sun252i-v861.dtsi (272 lines) + Avaota F2 board DT (43 lines) + its binding | 315 lines |
| 19 | MAINTAINERS entry for the V861 | +12 |
The SoC dtsi is the most checkable artifact in the series, because it is the vendor’s silicon described in
the kernel’s own vocabulary — and Guo Ren (XuanTie) has already reviewed the CPU, CLINT and PLIC parts
with a Reviewed-by. The cores carry compatible csky,c907: T-Head’s
XuanTie cores keep the historical “csky” vendor prefix in the kernel, the same convention the D1’s
C906 established. The interrupt controller reuses thead,c900-plic (150 sources) and
thead,c900-clint as fallback compatibles — again the D1 lineage. The PMU event
table is transcribed “from the V861 and C907 manuals”, and the commit message notes that
Zcb, Zbkc and Zvfh were verified working on actual hardware.
| Property | Value in sun252i-v861.dtsi |
|---|---|
| Cache | L1I/L1D 16 KiB each, 64 sets, 64 B block (4-way); L2 128 KiB unified, 128 sets |
| MMU / timebase | Sv39; 24 MHz timebase |
| Coherence | dma-noncoherent at the SoC bus |
| Base + scalar | i, m, a, f, d, c, b, zba, zbb, zbc, zbkc, zbs, zfa, zfh, zkt, zicond, zihintntl, zihintpause, zawrs |
| Vector | v, zvfh, zvfbfmin, zvfbfwma — FP16 and BF16 vector, no integer matrix extensions (zvbb/zvbc absent) |
| Bit-compressed | zca, zcb, zcd |
| Cache mgmt / PMU | zicbom, zicbop, zicboz, sscofpmf |
| Platform | zicsr, zifencei, zicntr, zihpm, sstc, svinval, svnapot, svpbmt, zfbfmin |
One reading of that string: an AI-camera SoC leans FP16/BF16 vector rather than integer matrix extensions, because the heavy INT8 lifting is assigned to the NPU while the C907 vector unit serves the ISP-adjacent image paths. It also means the mainline-visible core is not an RVA23-profile core — no Zacas, no Zabha, no Zicfilp/Zicfiss — so software built against the newest server profile assumptions should be tested, not assumed. The ISA string is the cheapest way to check any RISC-V chip’s real software surface; here it is committed to the tree where everyone can diff it.
| Layer | Vendor SDK (today) | Mainline (this series) |
|---|---|---|
| Kernel | linux-6.6-xuantie branch inside an OpenWrt 21.04 fork (Tina Linux 5.0) | 6.x mainline, ARCH_SUNXI |
| Boot target | Full product images: IPC / always-on-video / AI-glass profiles | Serial console on UART0 |
| Clocks / pins / RTC | Vendor tree | CCU + PRCM CCU + PIO/R-PIO + sun6i-rtc variants |
| Camera / ISP / NPU / codec | Vendor drivers | Not present |
| E907 | RTOS source tree (v861_e907) | Not present (no remoteproc) |
| Board hardware | — | Avaota F2 fully open (CC0), schematic to pick-and-place |
The gap column is the honest part of this story, but so is the trajectory. The D1 followed exactly this path: clock and pin controllers first, storage and USB next, a camera pipeline much later — and it is now the reference board-support example for cheap RISC-V Linux. The V861 starts from a stronger position in one specific respect: the board itself is open hardware from day one. The Avaota F2’s PDF schematic, EasyEDA Pro PCB, Gerbers, 3D STEP model, BOM and pick-and-place file are published under CC0, which means mainline bring-up and hardware documentation are in the same place at the same time — a pairing the D1 generation never had.
Guo Ren’s first review comment is a small but telling one: rather than listing specific SoC models in the
ARCH_SUNXI help text (which must be edited every time Allwinner ships another chip), keep it generic.
Expect the V2 to fold that in. Beyond review mechanics, the milestones that actually matter for this platform are:
(1) SD/NAND storage and USB, without which a serial console is all you can demo; (2) the MIPI CSI /
ISP / V4L2 path, which is the product’s entire reason to exist; (3) E907 remoteproc; (4)
whether anyone demonstrates the 1-TOPS NPU from mainline userspace. None of those are in this series, and none have
announced dates — which is the normal shape of mainline bring-up, and why the series’s own one-sentence
scope statement is the right contract to hold it to.
2026 年 11 月 13 日,中科院软件所工程师 Han Gao 通过 B4 向 RISC-V 与 devicetree
邮件列表提交了 19 个补丁(26 个文件,+2,080/−9 行),为全志 V861 摄像头 SoC 与
YuzukiHD Avaota F2 开发板增加 主线内核初始支持。这是 D1 之后第二颗进入主线的全志 RISC-V SoC,平台代号
sun252i。
V861 搭载 两颗玄铁 C907(RV64GCBV,最高 1.4 GHz)外加一颗跑 RTOS 的 E907(RV32IMAFC),带 4K@25fps
H.264/H.265 编码、1 TOPS INT8 NPU(官方名 “AI-ISP 2.0”)、片内封装 128 MB DDR3,目标产品是云台
AI 摄像头 / AI 眼镜。补丁内容刻意收窄:CCU(1,117 行)+ PRCM CCU + PIO/R-PIO 引脚控制器 + sun6i-rtc 时钟变体 + SoC dtsi
(272 行)+ 板级 dts,目标仅是串口启动。设备树记录了可核验的第一手规格:L1 各 16 KiB、L2 128 KiB 统一、
Sv39、DMA 非一致,兼容串沿用 D1 一脉的 thead,c900-plic/clint;C907 的完整 ISA 字符串(含
zvfh/zvfbfmin/zvfbfwma FP16/BF16 向量,无 Zacas/Zabha/整数矩阵扩展)随补丁入库,且 Zcb、Zbkc、Zvfh 已在
实机上验证。
诚实边界:本系列没有相机通路、V4L2、USB、存储、NPU 与视频编解码驱动,v1 尚未合并;玄铁的 Guo Ren 已 给出首条评审意见(Kconfig 帮助文本别逐个列 SoC 型号)。但 Avaota F2 板卡本身 CC0 完全开源(原理图到贴片 坐标),主线 bring-up 与硬件文档同日到位,这是 D1 时代不具备的起点。后续看点:存储与 USB、CSI/ISP/V4L2 相机通路、E907 remoteproc。
13 ноября 2026 года инженер Института программного обеспечения АН Китая (ISCAS) Han Gao
опубликовал серию из 19 патчей (26 файлов, +2,080/−9 строк), добавляющую
начальную поддержку в основное ядро Linux для камеры-SoC Allwinner V861 и платы YuzukiHD Avaota F2.
Это вторая RISC-V SoC Allwinner в mainline после D1; платформа получила имя sun252i.
V861 несёт два ядра XuanTie C907 (RV64GCBV, до 1,4 ГГц) плюс E907 (RV32IMAFC) под RTOS, кодек
H.264/H.265 до 4K@25fps, NPU на 1 TOPS INT8 («AI-ISP 2.0») и 128 МБ DDR3 в корпусе;
целевой продукт — поворотная AI-камера. Серия сознательно узка: CCU (1,117 строк) + PRCM CCU + контроллеры пинов
PIO/R-PIO + варианты sun6i-rtc + dtsi SoC (272 строки) + DT платы, цель — загрузка до последовательной
консоли. Device tree даёт проверяемые факты: L1 по 16 КиБ, L2 128 КиБ unified, Sv39, DMA non-coherent,
совместимости thead,c900-plic/clint (линия D1); полная строка ISA C907 (вектор FP16/BF16 zvfh, без
Zacas/Zabha/целочисленных матричных расширений), причём Zcb, Zbkc и Zvfh проверены на реальном железе.
Честная граница: нет пути камеры/V4L2, USB, хранения, NPU и кодеков; v1 не принята; Guo Ren (XuanTie) уже дал первую рецензию. Но сама плата Avaota F2 полностью открыта под CC0 — от схемы до файлов установки, чего у поколения D1 не было. Далее смотреть: накопители и USB, CSI/ISP/V4L2, remoteproc для E907.
El 13 de noviembre de 2026, el ingeniero Han Gao (Instituto de Software de la
Academia China de Ciencias, ISCAS) envió por B4 una serie de 19 parches (26 ficheros,
+2,080/−9 líneas) que añade soporte inicial del kernel principal para el SoC de cámara Allwinner
V861 y la placa YuzukiHD Avaota F2. Es el segundo SoC RISC-V de Allwinner en mainline tras el D1; la plataforma se
llama sun252i.
El V861 monta dos núcleos XuanTie C907 (RV64GCBV, hasta 1,4 GHz) más un E907 (RV32IMAFC) con RTOS,
codificador H.264/H.265 hasta 4K@25fps, una NPU de 1 TOPS INT8 («AI-ISP 2.0») y 128 MB de DDR3 en
el propio paquete; su producto objetivo es la cámara IA con panel giratorio. La serie es deliberadamente
estrecha: CCU (1,117 líneas) + PRCM CCU + controladores de pines PIO/R-PIO + variantes sun6i-rtc + dtsi del SoC
(272 líneas) + DT de la placa, con la meta de arrancar hasta una consola serie. El device tree aporta
datos verificables: L1 de 16 KiB, L2 unificada de 128 KiB, Sv39, DMA no coherente y los compatibles
thead,c900-plic/clint heredados del D1; la cadena ISA completa del C907 (vector FP16/BF16 zvfh, sin
Zacas/Zabha ni extensiones matriciales enteras) queda en el árbol, y Zcb, Zbkc y Zvfh están verificados en
hardware real.
Límite honesto: sin ruta de cámara/V4L2, USB, almacenamiento, NPU ni códecs; la v1 no está fusionada; Guo Ren (XuanTie) ya envió la primera revisión. A cambio, la placa Avaota F2 es hardware abierto CC0 desde el esquema hasta los ficheros de colocación, algo que la generación D1 nunca tuvo. Próximos hitos: almacenamiento y USB, ruta CSI/ISP/V4L2 y remoteproc del E907.
Le 13 novembre 2026, l'ingénieur Han Gao (Institut de logiciel de l'Académie
chinoise des sciences, ISCAS) a envoyé via B4 une série de 19 correctifs (26 fichiers,
+2,080/−9 lignes) ajoutant la prise en charge initiale du noyau principal pour le SoC caméra
Allwinner V861 et la carte YuzukiHD Avaota F2. C'est le deuxième SoC RISC-V d'Allwinner dans mainline après le D1 ;
la plateforme s'appelle sun252i.
Le V861 embarque deux cœurs XuanTie C907 (RV64GCBV, jusqu'à 1,4 GHz) plus un E907 (RV32IMAFC) sous
RTOS, un encodeur H.264/H.265 jusqu'à 4K@25fps, un NPU de 1 TOPS INT8 (« AI-ISP 2.0 ») et
128 Mo de DDR3 dans le boîtier ; le produit cible est la caméra IA sur cardan. La série est
volontairement étroite : CCU (1,117 lignes) + PRCM CCU + contrôleurs de broches PIO/R-PIO + variantes sun6i-rtc +
dtsi du SoC (272 lignes) + DT de la carte, avec pour objectif de démarrer jusqu'à une console série.
Le device tree livre des faits vérifiables : L1 de 16 Kio chacun, L2 unifiée de 128 Kio, Sv39, DMA non cohérent, et
les compatibles thead,c900-plic/clint hérités du D1 ; la chaîne ISA complète du C907 (vecteur FP16/BF16
zvfh, sans Zacas/Zabha ni extensions matricielles entières) entre dans l'arbre, et Zcb, Zbkc et Zvfh ont été
vérifiés sur le matériel réel.
Limite honnête : pas de chemin caméra/V4L2, pas d'USB, pas de stockage, pas de NPU ni de codecs ; la v1 n'est pas fusionnée ; Guo Ren (XuanTie) a déjà envoyé sa première revue. En contrepartie, la carte Avaota F2 est un matériel ouvert CC0, du schéma aux fichiers de placement — ce que la génération D1 n'avait pas. À suivre : stockage et USB, chaîne CSI/ISP/V4L2, remoteproc de l'E907.
Am 13. November 2026 reichte Han Gao (Institute of Software, Chinesische Akademie
der Wissenschaften, ISCAS) über B4 eine Serie von 19 Patches (26 Dateien, +2,080/−9
Zeilen) ein, die die anfängliche Mainline-Unterstützung für den Kamera-SoC Allwinner V861 und das Board YuzukiHD
Avaota F2 hinzufügt. Es ist der zweite Allwinner-RISC-V-SoC im Mainline-Kernel nach dem D1; die Plattform heißt
sun252i.
Der V861 trägt zwei XuanTie-C907-Kerne (RV64GCBV, bis 1,4 GHz) plus einen E907 (RV32IMAFC) unter
RTOS, einen H.264/H.265-Encoder bis 4K@25fps, eine 1-TOPS-INT8-NPU („AI-ISP 2.0“) und 128 MB DDR3 im
Gehäuse; das Zielprodukt ist eine schwenkbare KI-Kamera. Die Serie ist bewusst schmal: CCU (1,117 Zeilen) +
PRCM-CCU + Pin-Controller PIO/R-PIO + sun6i-rtc-Varianten + SoC-dtsi (272 Zeilen) + Board-DT, mit dem Ziel eines
Boots bis zur seriellen Konsole. Der Device Tree liefert überprüfbare Fakten: L1 je 16 KiB, L2 128 KiB
unified, Sv39, DMA non-coherent, die vom D1 geerbten Kompatiblen thead,c900-plic/clint; der vollständige
ISA-String des C907 (FP16/BF16-Vektor zvfh, ohne Zacas/Zabha und ohne Integer-Matrix-Erweiterungen) kommt in den Baum,
und Zcb, Zbkc und Zvfh wurden auf echter Hardware verifiziert.
Ehrliche Grenze: kein Kamera-/V4L2-Pfad, kein USB, kein Speicher, keine NPU, keine Codecs; v1 ist nicht gemerged; Guo Ren (XuanTie) hat bereits die erste Review geschickt. Dafür ist das Board Avaota F2 komplett offene Hardware unter CC0 — vom Schaltplan bis zu den Bestückungsdaten, was die D1-Generation nie hatte. Nächste Meilensteine: Speicher und USB, CSI/ISP/V4L2, Remoteproc für den E907.
در ۱۳ نوامبر ۲۰۲۶، مهندس Han Gao از مؤسسهٔ نرمافزار فرهنگستان علوم چین (ISCAS)
از طریق B4 سری ۱۹ وصلهای (۲۶ فایل، +۲٬۰۸۰/−۹ خط) را ارسال کرد که پشتیبانی اولیهٔ
هستهٔ اصلی لینوکس را برای SoC دوربین Allwinner V861 و برد YuzukiHD Avaota F2 اضافه میکند. این دومین SoC
RISC-V آلوینر در mainline پس از D1 است؛ نام پلتفرم sun252i گذاشته شده است.
V861 دارای دو هستهٔ XuanTie C907 (RV64GCBV، تا ۱٫۴ گیگاهرتز) بهعلاوهٔ یک E907 (RV32IMAFC) با RTOS،
رمزگذار H.264/H.265 تا 4K@25fps، NPU با توان 1 TOPS INT8 («AI-ISP 2.0») و ۱۲۸ مگابایت DDR3 داخل
بستهٔ چیپ است؛ محصول هدف آن دوربین هوشمند متحرک است. دامنهٔ این سری عمداً محدود است: CCU (۱٬۱۱۷ خط) + PRCM CCU +
کنترلکنندههای پایهٔ PIO/R-PIO + واریانتهای sun6i-rtc + dtsi سوسیک (۲۷۲ خط) + DT برد، با هدف بوت تا کنسول
سریال. درخت دستگاه حقایق قابل راستیآزمایی میدهد: L1 هرکدام ۱۶ KiB، L2 یکپارچهٔ ۱۲۸ KiB، Sv39، DMA ناهمواژه،
و سازگارهای بهارثرسیده از D1 یعنی thead,c900-plic/clint؛ رشتهٔ کامل ISA برای C907 (بردار FP16/BF16 با
zvfh، بدون Zacas/Zabha و بدون افزونههای ماتریسی صحیح) وارد درخت شده و Zcb، Zbkc و Zvfh روی سختافزار واقعی
آزموده شدهاند.
مرز صادقانه: مسیر دوربین/V4L2، USB، حافظه، NPU و کدکها وجود ندارند؛ v1 هنوز ادغام نشده و Guo Ren (XuanTie) نخستین بازبینی را فرستاده است. در عوض برد Avaota F2 سختافزار باز کامل با مجوز CC0 است — از شماتیک تا فایلهای استقرار؛ امری که نسل D1 هرگز نداشت. گامهای بعدی: حافظه و USB، مسیر CSI/ISP/V4L2، و remoteproc برای E907.